英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：


请选择你想看的字典辞典：
单词字典翻译
poursuite查看　poursuite　在百度字典中的解释百度英翻中〔查看〕
poursuite查看　poursuite　在Google字典中的解释Google英翻中〔查看〕
poursuite查看　poursuite　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • The 120% Rule Explained – 2011 NEC 705. 12(D)(2) - Pure Power
    In the 2011 National Electrical Code (NEC), the language in 705 12(D)(2) is straightforward: “Bus or Conductor Rating The sum of the ampere ratings of overcurrent devices in circuits supplying power to a busbar or conductor shall not exceed 120% of the rating of the busbar or conductor ”
  • 705. 12(D)(2) Bus or Conductor Ampere Rating. - ElectricalLicenseRenewal. com
    705 12(D)(2) Bus or Conductor Rating The sum of the ampere ratings of overcurrent devices in circuits supplying power to a busbar or conductor shall not exceed 120 percent of the rating of the busbar or conductor
  • MV SWITCHGEAR BUS BAR RATING - Mike Holts Forum
    Bus bar size inside switchgear is determined by building a structure subjecting it to a heat run test The bars are loaded to the the rated ampacity then the temperature is measured over a period of hours or until it is stabilized
  • Switchgear Compliance – Taps, Modifications, Interconnections – Part II . . .
    According to NEC 705 12B, when tapping or back feeding onto the load side, the sum of the current ratings of both source overcurrent protective devices (OCPDs) is allowed to exceed the current rating of the switchgear section bus by 20%
  • Article 408
    Conductors and busbars on a switchboard, switchgear, or panelboard shall comply with 408 3 (A) (1), (A) (2), and (A) (3) as applicable Location Conductors and busbars shall be located so as to be free from physical damage and shall be held firmly in place Service Panelboards, Switchboards, and Switchgear
  • MCC Bus Rating Sizing 6 - Eng-Tips
    Bottom line, use engineering judgement and be prepared to justify your sizing An inspector could hold you to sizing it for 100% of all loads plus 25% of the largest per the NEC For sizing overall system power demand, we've used 70% to 80% of the MCC connected load
  • Powell Technical Brief #24 Sizing Bus Bars in Switchgear and Motor Control
    This may be a good way to choose bus sizes for the mythical "single conductor in free air", but it isn't a satisfactory way to design buswork in practical equipments Consider the following chart, based on bus sizes used in our PowlVac® metal-clad switchgear: Switchgear Bus Rating 1200 A 2000 A 3000 A Number of bus bars per phase 1 1 2
  • NEC Medium Voltage Switchgear Design Requirement
    Switchgear designed for plant facilities shall meet the requirements of ANSI IEEE C37 20 2 Switchgear Ratings Voltage Ratings – The rated maximum voltage shall be 5, 15 and 38 kV as specified in below data sheet Frequency Rating – Rated voltage and current for switchgear shall be based on 60 Hz
  • Bus Bar Sizing And Circuit Breaker Sizing - LMPForum
    In a multi-motor circuit (per 430 53), your breaker must be NO LARGER than 250% of largest motor load plus the remaining FLCs, so (820-360) + (360 * 2 5) = 1360A If you put a 1600A or 2000A main breaker on that bus bar, it would violate the MAXIMUM rating required by the NEC You would use a breaker with trip settings at 1300A
  • Switchgear rating | Information by Electrical Professionals for . . .
    If I have a switchgear lineup with two buses and a tie with each bus rated for 65kA With the tie breaker open my available fault current is approx 43kA, which is acceptable per NEC If I close the tie breaker (both mains closed) my available fault current on either bus is approx 82kA





中文字典-英文字典  2005-2009